Stockfish's Tuning Method

From Chessprogramming wiki
Jump to: navigation, search

Home * Automated Tuning * Stockfish's Tuning Method

Stockfish's Tuning Method by Joona Kiiski, October 2011 [1] [2]

Introduction

The following tuning method was used to significantly improve Stockfish's playing strength (40-70 ELO points). The method is a practical approach and not mathematically very sound. Because algorithm is very simple, it's very likely already invented a long time ago. No pseudo- or source-code is given, just an idea behind the algorithm.

Step 1. Single variable

Let's assume that we have a single variable x which we want to tune. Current value for x is 100. We assume that this value is quite good (because we already have a strong engine), but not perfect. Next we need to choose delta for x. Delta must be big enough that engine(x = 100 - delta) and engine(x = 100 + delta) has at least a 1-3 ELO point difference. However delta must not to be too big, because then asymmetries start to play a big role. One just need to use his intuition here. Let's choose delta = 20.

Now we match engines engine(80) and engine(120) [self-play]. If engine 120 wins, we tune x slightly upwards. In our tuning sessions We successfully used apply_factor = 0.002. So in that case new value for x would be.

x = 100 + (120 - 100) * 0.002 = 100.04 

Next match would be engine(80.004) vs. engine(120.04)

In our tuning session we used 30000-100000 super-fast games, before reading final result.

Step 2. Varying delta

Instead of fixing delta, we fixed standard deviation of Gaussian distribution and calculated a random value for delta for each iteration. But again one needs to use his intuition to pick a suitable value for standard deviation.

Step 3. Multiple variables

Doing this for only one variable at a time would be a way too slow. Instead we used to tune 7-35 variables at the same time. As an example let's say that we have three variables:

 x = 100
 y = 100 
 z = 100

We would then calculate a random delta with sign for each of these variables based on Gaussian distribution. Let's say we get

 x_delta = +15
 y_delta = -10
 z_delta = +12

We then match engine(x=115, y=90, z=112) vs. engine(x=85, x=110, x=88). If first engine wins and apply_factor = 0.002 is used, new values are:

 x = 100 + (115 - 100) * 0.002
 y = 100 + ( 90 - 100) * 0.002
 z = 100 + (112 - 100) * 0.002

With 30000-100000 super-fast games, we usually got some improvement compared to only by hand tuned values.

Pros and Cons

What actually happens with multiple variables is that most important variables shall dominate and they shall approach their optimal values, while less important variables take "a random walk". In the beginning this increases strength. But after a while important variables stop approaching optimal values and "random walk" takes over and the strength starts to decrease. So the method doesn't converge and it needs to be stopped at "suitable moment". This is a big problem as well as manual selection of deltas (or standard deviation of delta).

Most other tuning algorithms start "from scratch". Although we know a value which is very close to optimal, they make no use of it. They start matching engine(x=0) vs. pool of other engines and engine(x=200) vs. pool of other engines. And it takes tens of thousands or hundreds of thousands iteration before they can even reach the current level (x=100) and only after that we can get some improvement. Instead method described in here starts from that "very good" value and attempts to improve it slightly.

Variable Selection

Variable selection is extremely important. for example if you tune each piece-square table value separately, you are doomed the fail, because changing only one value is going to change the strength of the program only very little. So in tuning we end up doing only random walk and the strength of the program only goes slightly downhill.

But instead using ampli-bias knobs for tables proved to be very successful approach for us. Each value for the table is adjusted using these two knobs like (Here we optimize variables var_bias and var_amplitude):

 new_value = orig_value + var_bias + orig_value * var_amplitude / 100

Each chess engine is full of different kind of tables and if we can give even "a slight push" for each of these tables, it'll result in considerable increase in the end.

See also

Publications

Forum Posts

Re: Stockfish's tuning method by Rémi Coulom, CCC, October 07, 2011

External Links

References

Up one Level